Recent Updates

Perusahaan Uniflex Sdn Bhd updated website's banner
Sep 23, 2022 at 01:51 pm —
Perusahaan Uniflex Sdn Bhd added 2 new photos
Jul 4, 2022 at 03:24 pm —
Perusahaan Uniflex Sdn Bhd updated NEWPAGES Profile
Jul 10, 2018 at 03:06 pm —
Perusahaan Uniflex Sdn Bhd updated NEWPAGES Profile
Jun 6, 2018 at 02:44 pm —
Perusahaan Uniflex Sdn Bhd added 6 new photos in Other Products & Services
Jun 5, 2018 at 04:15 pm —
Perusahaan Uniflex Sdn Bhd added new photo in Polyurethane Screen Media
Jun 5, 2018 at 04:14 pm —
Molded Screen Cloth with Reinforced Fabric & Side Hook

Molded Screen Cloth with Reinforced Fabric & Side Hook

6x16 Primary Waste Screen with feed size of minus 6 bypassed the Jaw Crush These rubber screen clothes with nylon fabric reinforced are flexible and light weight. It can replace the wire mesh without any modification of screen deck. The openings are moulded with tapper profile to reduce pegging or conventionally punched are used for light duty applications and for nominal sizing from 5mm to 100mm. The thickness of the rubber screen cloth ranged from 6mm to 60mm and can readily replace the wire mesh without screen deck modification. The disadvantage is poor definition of apertures with punching process, therefore not suitable for precise and efficient screening. Full width fabric reinforced panel with punched holes read more
Perusahaan Uniflex Sdn Bhd added new photo in Full Width Moulded Panels with Steel Backing
Jun 5, 2018 at 04:08 pm —
Full Width Molded Panels with Steel Backing

Full Width Molded Panels with Steel Backing

40mm thick full width panel with side hook and centre hold-down bar for 5x14 scalping This design can easily install onto existing screen deck with minimum modification. The thickness ranged from 40mm to 80mm with full steel backing. Side hook can be bended on backing plate for easy installation. The openings are moulded with tapered profile to reduce pegging and typically used in heavy duty scalping and nominal sizing with aperture above 50mm. read more
Perusahaan Uniflex Sdn Bhd added new photo in Modular Moulded Panels with Steel Backing
Jun 5, 2018 at 04:03 pm —
Modular Molded Panels with Steel Backing

Modular Molded Panels with Steel Backing

The modular panels are designed for heavy duty scalping screen with very high wear rate. The thickness ranged from 40mm to 100mm with full steel backing and moulded in smaller panel size, so that it is lighter and easier to install. This design is more cost-effective especially there are uneven and localized wear. 80mm thick Modular Rubber Screen Panel for feed size exceeding 6. To avoid plugging, 120mm square holes are moulded with special profile. 60mm thick Modular Panels with 70 mm square and tapered hole profile. read more
Perusahaan Uniflex Sdn Bhd added new photo in Vibrating Screen Media
Jun 5, 2018 at 03:29 pm —
MODUMESH™ Screening Media

MODUMESH™ Screening Media

Malaysian Industrial Design No. : MY 11-00526-0102 & MY 11-00527-0202 Indonesian Design Registration No. : ID 0032777-D & ID 0032778-D Vietnamese Design Patent No.17509 Thai Design Patent No.46487 Modumesh is a new design of modular screen panel with nominal size of 320 x 500 which will be installed on special support frame. The interlocking and boltless design requires minimum support on panel and therefore increases surface area for screening purpose. The panel also moulded with flow diverters to direct the flow of material over the holes. Interlocking Side Liners are incorporated into the design for better protection of machine side plates without additional bolts and nuts. The effective open areas are very high, exceeding 50% for 52mm apertures. The buckle bars are completely covered. 52 x 52mm Square Holes 34 x 36mm Rectangle Holes Blinding and pegging problem with wire mesh and polyurethane rectangle holes Practically no blinding and pegging with Modumesh screen media. 5mm separation with Modumesh system for 3.0m x 7.5m screen size at Holcim Malaysia. Modumesh manufactured with injection moulding process gives more precise hole dimension. Modumesh panel is built in with flow diverters which funnel the materials towards the holes and help to align the material flow along the screen length. Tapered hole design minimize chances of pegging compare to hour glass profile of punched screen cloth. Higher percentage of effective open area means higher screening efficiency. Uneven wear rate cost expensive replacement of full width tensioned screen cloth whereas Modumesh system only needs to change a small section of worn panels. Maintenance free as Modumesh system does not need to tension throughout the working life span. Modumesh design incorporate with rubber side liners which protect the expensive side plate of screen machine. Cost saving and fewer spare parts because there are no clamping bars, central attachments, hooks, tensioning bolts and rubber channel. Mix the different apertures to meet the products specifications. Easier and faster installation with Modumesh system. read more
next page

Switch to Mobile Version